1. COR IB R 1 1 0 0 / IB R 1 1 50 (Integrated Broadband Router) SIM CARD SETUP Q UIC K S T A R T G UI D E S ET T I N G UP THE ROUTER 1 ) Purchase a data plan. Then insert the SIM as shown on page 2. 2 ) Connect WiFi, modem and GPS antennas as desired. (Sold separately.) Finger tight only. 3 ) Wire power cable to 9-36v power source. (AC power supply sold separately.) ACCESSING THE ADMINISTRATION PAGES 6 7 8 5 2 3 4 For more information about your product, visit: cradlepoint.com cradlepoint.com/IB R 1 1 0 0 To learn more about features, visit To make configuration changes to your router, open the IBR 1 1 0 0’s GUI-based administration pages. 1) Connect via Ethernet or WiFi. For WiFi, the default SSID is IB R 1 1 00- xxx (last 3 characters of the MAC address). 2) Open a browser window and type “ cp/ ” or “ 1 92 . 1 6 8.0 . 1 ” in the address bar. Press ENTER/RETURN . 3) When prompted for your password, type the eight character DEFAULT PASSWORD found on the product label. To insert or remove SIM card: 1) Remove bottom SIM cover. 2) Slide metal latch down to unlock. 3) Pull cartridge upward, so it is standing at a 90° angle. 4) Insert SIM card with metal contacts down and notch out. 5) Press cartridge back into place. 6) Return metal latch to start (lock) position. 7) Replace bottom SIM cover. Note: Device will not power on without cover in place. Find this label on the bottom of your router. Warning: This product is only to be installed by qualified personnel! For product available in the USA/Canada market, only channel 1 – 11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter. Industry Canada Statement This device complies with RSS-210, RSS-102, and RSS-Gen of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire d operation. IMPORTANT NOTE: Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be i nstalled and operated with minimum distance 25cm between the radiator and your body. This device has been designed to operate with cellular antennas having a maximum gain of 3 dBi. Antennas having a higher gain a re strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. This device has been designed to operate with WiFi antennas having a maximum gain of 5 dBi. Antennas having a higher gain are s trictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. Déclaration d’Industrie Canada Ce dispositif est conforme à la norme CNR-210, CNR-102, et CNR-Gen d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accept er tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. NOTE IMPORTANTE (Pour l’utilisation de dispositifs mobiles): Déclaration d’exposition aux radiations Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équip ement doit être installé et utilisé avec un minimum de 25 cm de distance entre la source de rayonnement et votre corps Ce dispositive a ete concu pour fonctionner ave une antenna cellulaire ayant un gain maximal de 3 dBi. Une antenne a gain plus eleve est strictement interdite par les reglemnets d’Industrie Canada. L’impedance d’antenne requise est de 50 ohms. Ce dispositive a ete concu pour fonctionner ave une antenna WiFi ayant un gain maximal de 5 dBi. Une antenne a gain plus eleve est strictement interdite par les reglemnets d’Industrie Canada. L’impedance d’antenne requise est de 50 ohms. INFORMATION FOR EUROPE, DECLARATION OF COMPLIANCE CradlePoint, Inc declares that the IBR1100 / IBR1150 is in compliance with the essential requirements of the R&TTE Directive 1 999/5/EC, Energy Related Products Directive 2009/ 1 25/EC, Electromagnetic Compatibility Directive 2004/ 1 08 / EC, Low Voltage Directive 2006/95/EC, and RoHS2 Directive 2011/65/EU. THE FIRST TIME SETUP WIZARD PORTS & SWITCHES When you log in for the first time, you are automatically directed to the FIRST TIME SETUP WIZARD , which will help you customize your COR IBR 1 1 0 0 . Change any of the following: Administrator password Time zone WiFi network name, security mode, and password Access Point Name (APN) for SIM-based modems WAN failure check mode If you are currently using the IBR 1 1 0 0 WiFi network, you will need to reconnect your devices to the network using the newly established wireless network name and password. NOTE: To return to the First Time Setup Wizard after your initial login, s elect GETTING STARTED on the top navigation bar and FIRST TIME SETUP in the dropdown menu. FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may n ot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25cm between the radiator & your body. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, for the IBR 1 1 00 and IBR 1 1 50, the maximum antenna gain in the cellular bands must not exceed 3dBi. For the IBR 1 1 00, the maximum WiFi antenna gain in the 2.4 and 5 GHz bands must not exceed 5dBi. SAFETY AND HAZARDS This equipment is designed to operate in ambient temperatures up to 70°C (158° F). When operating in elevated ambient temperat ures, the surface of the equipment may exceed 70°C and become too hot to safely touch. Under this condition, this product must be installed in a secure d location that is not accessible to accidental touch, and access to the device must be restricted to service persons or users who possess the proper tool or key to access the device and have been informed about the potential high surface temperatures and instructed on how to safely handle and/or service the device. Under no circumstances should the IBR 1 1 00 device be used in any areas (a) where blasting is in progress, (b) where explosive atmospheres may be present, or (c) that a re near (i) medical or life support equipment, or (ii) any equipment which may be susceptible to any form of radio interference. In such ar eas, the IBR 1 1 00 device MUST BE POWERED OFF AT ALL TIMES (since the device otherwise could transmit signals that might interfere with such equipment). In addition, under n o circumstances should the IBR 1 1 00 device be used in any aircraft, regardless of whether the aircraft is on the ground or in flight. In any aircraft, the IBR 1 1 00 device MUST BE POWERED OFF AT ALL TIMES (since the device otherwise could transmit signals that might interfere with various onboard systems on such aircraft). Furthermore, under no cir cumstances should the IBR 1 1 00 device be used by the driver or operator of any vehicle. Such use of the device will detract from the driver’s or operator’s control of that vehi cle. In some jurisdictions, use of the IBR 1 1 00 device while driving or operating a vehicle constitutes a civil and/or criminal offense. Due to the nature of wireless communications, transmission and reception of data by the IBR 1 1 00 device can never be guaranteed, and it is possible that data communicated or transmitted wirelessly may be delayed, corrupted (i.e., contain errors), or totally lost. The IBR 1 1 00 device is not intended for, and CradlePoint recommends the device not be used in any critical applications where failure to transmit or receive data could result in property damage or loss or personal inju ry of any kind (including death) to the user or to any other party. CradlePoint expressly disclaims liability for damages of any kind resulting from: (a) delays, errors, or losses of any data transmitted or received using the device; or (b) any failure of the device to transmit or receive such data. For proper and safe vehicle installations, the GPIO accessory cable must be connected to a fused circuit in the vehicle. This f used circuit requires a 2A fuse. If the supply connection is made directly to the battery, the fuse should be installed in the positive lead. For North America, a UL Listed f use is to be used. This important Product Information and Safety Guide contains safety, handling, disposal, regulatory, trademark, copyright, and software licensing information. Read all safety information below and operating instructions before using the IBR 1 1 00 device to avoid injury. FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference i n a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica - tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cau se harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one o f the following measures: • Reorient or relocate the receiving antenna. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. A copy of the original European DoC may be obtained from cradlepoint.com/product-certifications AT BE BG CY CZ DK EE FI FR DE GR HU IE IT LV LT LU MT NL PL PT RO SK SI ES SE GB IS LI NO CH TR Operation of the device in the 5150-5250 MHz frequency band is restricted to indoor use only. To comply with RF Exposure requirements, the product must be installed and operated with a minimum separation distance of 25 cm between the antennas and nearby persons. RECYCLING AND ENVIRONMENTAL INFORMATION To find information on CradlePoint’s commitment to our environment and how to responsibly recycle CradlePoint products, please visit cradlepoint.com. OPEN SOURCE SOFTWARE This product contains software distributed under one or more of the following open source licenses: GNU General Public License Version 2, BSD License, Net-SNMP License, and PSF License Agreement for Python 3.3. For more information on this software, including licensing terms an d your rights to access source code, contact CradlePoint at www.cradlepoint.com/opensource. WARRANTY INFORMATION CradlePoint, Inc. warrants this product against defects in materials and workmanship to the original purchaser (or the first pu rchaser in the case of resale by an authorized distributor) for a period of one (1) year from the date of shipment. This warranty is limited to a repa ir or replacement of the product, at CradlePoint’s discretion as purchaser’s sole and exclusive remedy. CradlePoint does not warrant that the operation of the device will meet your requirem ents or be error free. Within thirty (30) days of receipt should the product fail for any reason other than damage due to customer negligence, purchaser may return the product to the po int of purchase for a full refund of the purchase price. If the purchaser wishes to upgrade or convert to another CradlePoint, Inc. product within the thirty (30) day period, pu rchaser may return the product and apply the full purchase price toward the purchase of another CradlePoint product. Any other return will be subject to CradlePoint, Inc.’s existing retu rn policy. LIMITATION OF CRADLEPOINT LIABILITY The information contained in this Quick Start Guide is subject to change without notice and does not represent any commitment o n the part of CradlePoint or its affiliates. CRADLEPOINT AND ITS AFFILIATES HEREBY SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL: ( A) DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES, INCLUDING WITHOUT LIMITATION FOR LOSS OF PROFITS OR REVENUE OR OF ANT ICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE THE DEVICE, EVEN IF CRADLEPOINT AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF T HE POSSIBILITY OF SUCH DAMAGES, AND EVEN IF SUCH DAMAGES ARE FORESEEABLE; OR (B) CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall th e aggregate liability of CradlePoint and/or its affiliates arising under or in connection with the device, regardless of the number of events, occurrences, or claims givin g rise to liability, exceed the price paid by the original purchaser of the device. PRIVACY CradlePoint collects general data pertaining to the use of CradlePoint products via the Internet including, by way of example, IP address, device ID, operating system, browser type and version number, etc. To review CradlePoint’s privacy policy, please visit: cradlepoint.com/privacy. OTHER BINDING DOCUMENTS; TRADEMARKS; COPYRIGHT By activating or using your IBR 1 1 00 device, you agree to be bound by CradlePoint’s Terms of Use, User License and other Legal Policies, all as posted at cradlepoint.com/legal. Please read these documents carefully. © 2 0 1 4 CradlePoint, Inc. All rights reserved. CradlePoint is not responsible for omissions or errors in typography or photography. CradlePoint, IBR 1 1 00, WiPipe™, the WiPipe logo, and the CradlePoint logo are trademarks of CradlePoint, Inc. in the US and other countries. Other trademarks are property of their respective owners. Part Number: 170650-001 UPDATING FIRMWARE ACTIVATE YOUR MODEM A wireless broadband data plan must be added to your IB R 1 1 00. Wireless broadband data plans are available from wireless carriers such as Sprint, Verizon, AT&T, EE, Vodafone, and Clearwire. Mobile broadband, M2M, and router pricing plans are available. To add or transfer a line of service you will need to provide the IMEI/MEID for LTE modems. LTE plans also require a SIM. SIM provisioning for LTE models is done the same way as for USB modems. Once provisioned insert the SIM into the router as shown on page 2. For more information on activation see cradlepoint.com/activation. See Product Manual for suggested antenna positions. RESET: To restore the COR IBR 1 1 00 to its factory default settings, press and hold the RESET button on the side of the device for ten seconds. Reset returns the login password to the DEFAULT PASSWORD and resets all configuration changes. Log into the administration pages (see page 3). You may have changed the ADMINISTRATOR PASSWORD when you used the FIRST TIME SETUP WIZARD . Select SYSTEM SETTINGS on the top navigation bar, then SYSTEM SOFTWARE in the dropdown menu. Find the FIRMWARE UPGRADE section. This displays the current firmware version that is installed and indicates if updated firmware is available. Click AUTOMATIC (Internet) if new firmware is available. The IB R 1 1 00 will download and install the firmware and automatically reboot itself. A status monitor will appear and indicate when this process is complete. This process may take several minutes depending on your Internet connection speed. 1) 2) 3) 4) CradlePoint regularly creates new firmware packages. You may need to update firmware to use the IB R 1 1 00 with new modems and to access our latest features. HOW TO UPDATE FIRMWARE CRADLEPOINT ENTERPRISE CLOUD MANAGER NEXT GENERATION NETWORK MANAGEMENT AND APPLICATION PLATFORM Rapidly deploy and dynamically manage networks at geographically distributed stores and branch locations with Enterprise Cloud Manager, CradlePoint’s next generation application platform that will improve productivity, increase reliability, reduce costs, and enhance the intelligence of your network and business operations. Subscription required. See cradlepoint.com/ecm for details. If your device does not have an active Internet connection, you need to download the latest firmware from cradlepoint.com/firmware to your desktop. Then use the MANUAL FIRMWARE UPLOAD option. NOTE: Access to firmware upgrades requires a CradleCare Support Agreement or Enterprise Cloud Manager. What’s In The Box Quick Start Guide Power/GPIO Cable Sold separate: AC Power Supplies, WiFi Antennas, GPS Antennas, Cell Antennas. Integrated Broadband Router POWER 9-36VDC WiFi ANTENNA CONNECTOR (RSMA, 2.4/5 GHz) WiFi ANTENNA CONNECTOR (RSMA, 2.4/5 GHz) ( LAN ) default ETHERNET CONNECTIONS ( W A N ) default USB ( Standard-A ) RS-232 ( Female ) MAIN MODEM ANTENNA CONNECTOR (SMA) GPS POWER LED USB LED SIGNAL STRENGTH LED S W i F i LED s M O D E M LED AUXILIARY MODEM ANTENNA CONNECTOR (SMA) POWER/ RESET Find this label on the bottom of your router. The IBR 1 1 00 and IBR 1 1 50 come with an active GPS connection at 3.3 V and 1 00 mA max. For full functionality you will need to use an active GPS antenna. TAIP and NMEA Protocol Support. GPS Metal latch Notch IB R 1 1 00 IB R 1 1 50 SPECIAL FEATURES • IPSec VPN End-Point Support • GRE Tunneling • Data Usage Management & Alerts • GPIO Interface • GPS • Load-Balancing & Failover/Failback • WiFi Hotspot Services (Captive Portal) • IP Passthrough • WiFi as WAN & Dual SSIDs • VLAN Support • CradlePoint Enterprise Cloud Manager • USB to Serial Console Passthrough Support • LAN/WAN Affinity • BGP/OSPF/RIP • VRRP • Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help.